Study guide · Course, compass and position fixing
Mastering course, compass and position fixing
At sea you draw a course on the chart, steer it by compass and check along the way where you really are. In between lie a few conversions you need to handle with confidence. On this page you learn the difference between speed through the water and speed over the ground, the three norths, and how to convert courses and bearings. After that come current, the DR position and the position offset, and the methods you use to fix your position. As a running example, you sail a day's passage along an unfamiliar coast. The page is based on the official German catalogue for the Coastal Skipper Certificate, known as the SKS, but it is written in its own words.
Through the water and over the ground
The usual log on board measures how fast the boat moves relative to the surrounding water. This is the speed through the water, or STW. If the water itself is moving, as it does in a current, the boat moves differently over the ground. GPS measures its position relative to the earth. It therefore shows speed over ground (SOG) and course over ground (COG).
To work out the speed over ground from the log, you need two more pieces of information: the direction and the rate of the current. If the current runs exactly from astern, you add the two values. If it runs exactly from ahead, you subtract it.
Current is sometimes given in metres per second. A rule of thumb: metres per second times 2 gives knots. The exact factor is 1.94, but 2 is good enough for planning.
For distance and time there is a simple formula: distance equals speed times time. You enter the time in hours. 36 minutes are 0.6 hours, so at 5 knots you cover 3 nautical miles.
The three norths
Navigation uses three different directions for north. Once you can tell them apart, every course conversion makes sense.
- True north is the direction of the meridian to the geographic North Pole. Charts, GPS and all nautical publications refer to it.
- Magnetic north is the direction of the earth's magnetic field towards the magnetic North Pole. An undisturbed compass needle would point there.
- Compass north is the direction your boat's compass actually points to. It is also deflected by the boat's own magnetic field.
Between these three directions lie three angles.
- Variation (Var) is the angle between true north and magnetic north.
- Deviation (Dev) is the angle between magnetic north and compass north.
- Compass error (CE) is the angle between true north and compass north. It is the sum of the other two: CE = Dev + Var.
The signs follow a fixed rule. If the magnetic direction lies east of the reference direction, the value is east and positive. If it lies west, it is west and negative. A variation of 3 degrees east is written as plus 3 degrees, a deviation of 4 degrees west as minus 4 degrees.
Variation and deviation
Variation depends on position and year, because the earth's magnetic field changes slowly. At the same place and in the same year it is the same for every vessel. You find it in the compass rose on the chart, together with the reference year and the annual change. For the current passage you update it to the present year. How to do that is explained on the learning page about charts, nautical publications and lights.
Deviation is caused by the iron, the engines and the electrical equipment on board. Every vessel has a different magnetic field. That is why every vessel needs its own deviation table, the deviation card. Deviation depends on the heading. When you change course, the boat and its magnetic field turn underneath the compass needle, and the deviation changes.
If your course is not in the table, you interpolate between the two neighbouring values.
Deviation changes permanently when something changes on board. Examples are a new engine, new installations, or a heavy iron object that gets a new fixed place near the compass. Then you must check the table or have a new one made. Apart from that, you check the compass regularly. One way is a transit whose true direction you know from the chart.
Anything that can be magnetised belongs at least 1 metre away from the magnetic compass. That also applies to small things like a mobile phone, a pocket knife or a can of beer.
For taking bearings you use a hand bearing compass. A ball compass can still be read when the boat heels a lot. That is its advantage over a binocular compass, which quickly becomes inaccurate at a steep angle of heel.
Converting courses
Converting means turning a course from one north into another. The basic equation is:
True course = compass course + Dev + Var
From compass to chart, you add deviation and variation with their signs. From chart to compass, you work backwards and subtract both: compass course = true course − Var − Dev.
- Read the true course off the chart.
- Update the variation to the current year and subtract it. This gives the magnetic course.
- Look up the deviation for this course in the deviation card and subtract it too. The result is the compass course you steer.
The same mistakes happen again and again in this calculation.
- The variation from the chart is not updated to the current year.
- The deviation is taken for a bearing instead of for the course.
- Easterly values are treated as minus instead of plus.
Converting bearings
If you take a bearing of an object with the steering compass, you get a compass bearing. Before you draw it on the chart, you convert it to true, just like a course. There is one difference. The deviation is not taken for the direction of the bearing, but for the heading. Deviation comes from the boat, and the boat lies on its course wherever you happen to look.
Current and leeway
A current moves the whole body of water, and your boat with it. Wind also pushes the boat sideways through the water. You have to allow for both when you plan your course.
The current triangle shows the effect of a current. From your position, draw the course and speed through the water for one hour. From its end, add the current for one hour. The line from start to end gives course and speed over the ground.
If you want to hold an exact course over the ground, you have to steer into the current. In other words, you aim a little upstream.
You can also measure the current. Compare the log with the GPS. If the course over ground matches your course but the speed over ground is lower, the current is running straight against you.
If the compass and GPS show different courses, say 30 degrees on the compass and 45 degrees over the ground, there are two possible causes. Current or wind is setting the boat off. Or you forgot that the compass differs from true north by the compass error.
Leeway is the angle by which the wind pushes the boat to leeward. It is most noticeable close-hauled. You estimate it and allow for it when you plot. If the wind comes from starboard, the boat drifts to port. The course through the water is then smaller than the course steered.
Dead reckoning and position offset
Dead reckoning means working out from course, speed and time where you should be now. The result is the DR position. A position you have fixed with bearings, distances or GPS is called the observed position, or fix.
You plot the boat's position on the chart at regular intervals. That way you notice early if you are drifting off the course line. If the DR position and the observed position differ at the same time, that difference is the position offset, in German Besteckversetzung or BV. It is given as direction and distance from the DR position to the observed position.
A position offset can have three causes.
- Inaccurate steering and plotting.
- Course errors, for example from an inaccurate deviation card.
- Current and wind that were not allowed for, or allowed for wrongly.
The Baltic has hardly any tides. There, it is mainly the strength, duration and direction of the wind that cause considerable changes in water level and wind-driven currents. After a few days of strong wind from one direction, expect a noticeable current.
If the offset is large, look for the cause: current, steering, deviation card. Then continue your dead reckoning from the observed position, not from the old DR position. Otherwise you carry the error forward.
Fixing your position
With bearings and distances to objects on land you can fix your position without GPS. This is called terrestrial position fixing. Every bearing and every distance gives a position line. Where two position lines cross, that is where you are.
Cross bearing: you take bearings of two known objects. The angle between the two bearings should be between 30 and 150 degrees. A cut close to 90 degrees is the most accurate. With very acute or very obtuse angles, even a small bearing error moves the crossing point a long way.
If you have only one object in sight, for example a single lighthouse, two methods remain.
- Bearing and distance: you measure the distance with radar or work it out with the light on the horizon method.
- Bearing and sounding: you compare the measured depth with the depths along the bearing line. This only works if the seabed there rises regularly and steeply enough. On a flat, even seabed the same depth fits in many places.
When plotting, remember the direction. The bearing points from the boat to the object. Your position therefore lies in the opposite direction as seen from the object.
Equipment and night passages
Even on a short coastal trip, a yacht needs at least four things. These are a steering and hand bearing compass, a sounding device, a log and a clock. For navigating in coastal waters you add binoculars, a barometer and the logbook. GPS replaces none of these. If it fails, you have to manage with them.
Prepare a night passage beforehand, in daylight.
- Work out all courses and waypoints where you change course in advance.
- Highlight shallows and obstructions clearly on the chart.
- Mark where each light will appear on the horizon, so you can recognise it at once and use it for a distance.
Key points
- The log measures speed through the water, GPS shows course and speed over the ground. For the speed over ground you need the direction and rate of the current.
- Metres per second times 2 gives roughly knots. Distance equals speed times time in hours.
- Variation lies between true and magnetic north, deviation between magnetic and compass north. CE = Dev + Var.
- East is plus, west is minus.
- Variation depends on position and year and is shown on the chart. Deviation depends on the heading and is listed in the boat's own deviation card.
- True course = compass course + Dev + Var. From chart to compass you subtract.
- A bearing taken with the steering compass is corrected with the deviation for the heading.
- Anything magnetisable stays at least 1 metre from the compass. New installations require a new deviation card.
- Against a current you steer upstream. Leeway pushes the boat to leeward.
- The position offset points from the DR position to the observed position. Dead reckoning continues from the observed position.
- Cross bearings should cut at between 30 and 150 degrees. With only one object, use bearing and distance or bearing and sounding.
Terms
- Speed through the water
- The speed relative to the surrounding water, measured by the log.
- Speed over ground
- The speed relative to the seabed, shown by GPS.
- True north
- The direction towards the geographic North Pole.
- Magnetic north
- The direction of the earth's magnetic field towards the magnetic North Pole.
- Compass north
- The direction in which the boat's compass actually points.
- Variation
- The angle between true north and magnetic north.
- Deviation
- The angle between magnetic north and compass north, caused by the boat itself.
- Compass error
- The sum of deviation and variation.
- Deviation card
- The deviation table of one particular boat for different headings.
- Converting
- Turning a course or bearing from one north into another.
- Steering into the current
- Aiming upstream in order to hold a course over the ground.
- Leeway
- The angle by which the wind sets the boat to leeward.
- DR position
- The position worked out from course, speed and time.
- Observed position
- The position fixed by bearings, distances or GPS.
- Position offset
- Direction and distance from the DR position to the observed position.
- Cross bearing
- A position fix using the bearings of two known objects.
- Position line
- A line on which the boat must lie, obtained from a bearing, a distance or a sounding.